110/04 P/N 21196804© COPYRIGHT 2004 by HUFFY SPORTSInground SystemOwners ManualCustomer Service Center• N53 W24700 South Corporate Circle • Sussex, WI
10P/N 21196804 10/0443Fill hole completely with concrete.6.1" (2.54 cm)51" (2.54 cm)7.Tamp down concrete to release air pockets and build dr
10/04 P/N 2119680411After concrete has cured, remove bottom pole section from ground sleeve (4). Place anti-skid tape (36)around the bottom area of bo
12P/N 21196804 10/04159.Stack and bounce bottom (3) and middle (2)pole sections together. Bounce pole sectionstogether until middle section no longer
10/04 P/N 211968041314077FRONT SIDE11.Install pole mount bracket (6) and bracket reinforcement (40) with carriage bolts (7) as shown. Tighten flange n
14P/N 21196804 10/04126121313119101012. 681414171513. Attach spacers (12, 13) to pole mount bracket (6) with bolts (9), washers (10), andnuts (11) as
10/04 P/N 211968041520193837211814.2015.16Insert handle assembly throughpole mount assembly as shown.Lock pole assembly in place atthe 10’ (3.05 m) ma
16P/N 21196804 10/04SECTION B: ASSEMBLE THE ELEVATOR TUBES TO BACKBOARD30Upper Elevator tube28Identify elevator tubes (28 & 30).9/16”3/4”1/2”(2) W
10/04 P/N 2119680417Attach backboard support brackets (25) to the backboardframe using bolts (9), spacers (31), and nuts (11) as shown. 1.253131911911
18P/N 21196804 10/0422242828302725303. 2922Attach upper elevator tubes (30) to backboard support brackets (25) using spacers (22), bolt (27), and nut(
10/04 P/N 2119680419SECTION C: ATTACH THE BACKBOARD & ELEVATOR ASSEMBLYTO POLE SYSTEM3/4”#27#46#24#45#23#39#44#43#33TOOLS REQUIRED FOR THIS SECTIO
2P/N 21196804 10/04BEFORE YOU START!To ensure optimal playability of backboard system, aclose tolerance fit between the elevator componentsand hardwar
20P/N 21196804 10/041.1243030232323232428282.Support pole on sawhorse. Attach backboard assembly to top pole section (1). Install handle assembly to l
10/04 P/N 21196804213.4346454142Install Slam Jam Rim to Backboard 3244424546ABCDEA • Fit rim (32) securely into bracket (41) as shown (Allow "T&q
22P/N 21196804 10/044.2427303029Insert bolt (27) through left side of short elevator tube (30), then stretch spring or springs (29) onto bolt(27). Ins
10/04 P/N 2119680423Place rebar with spacers into bottom pole section (3)as shown. .6.Assemble rebar centering spacers(50) near top and bottom of reba
24P/N 21196804 10/04Fill pole with concrete to approximately 1” (2.54 cm)below bottom elevator hole as shown. IMPORTANT!: WAIT A MINIMUMOF 24 HOURS BE
10/04 P/N 21196804259.Install clips.Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so thatsecond “arm” slides over the top
26P/N 21196804 10/04Twist net until it snaps into position. Net must be centered through clip. NET INSTALLATION10. 323334Insert net intobottom of clip
10/04 P/N 2119680427SECTION D: UPRIGHT, SECURE AND USE POLE SYSTEMWedgeHammerNoneThis is what your system will look like when you’vefinished this sec
28P/N 21196804 10/0452.1.After concrete has cured, remove tape, install pole cap (26), fit pole assembly into sleeve (4). Use wedge to gently tap cap
10/04 P/N 21196804294.16B.A.C.3.A. While holding handle, remove pin (16).B. Move elevator up or down to desired height.C. Replace pin (16) full length
10/04 P/N 211968043For more information on assembly, placement, properuse, and maintenance, visit The American BasketballCouncil website at http://www
4P/N 21196804 10/04SAFETY INSTRUCTIONSMost injuries are caused by misuse and/or not following instructions.Use caution when using this system.• If usi
10/04 P/N 211968045#8 (9)*#10 (4)HARDWARE IDENTIFIER (BOLTS & SCREWS)HARDWARE IDENTIFIER (NUTS & WASHERS)HARDWARE IDENTIFIER (METAL SPACERS)#1
6P/N 21196804 10/04#44 (1)#41 (1) #43 (1)HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS)HARDWARE IDENTIFIER (OTHER)#23 (4)#22 (4)#12 (2)#39 (2)#33 (
10/04 P/N 211968047TOOLS REQUIRED FOR THIS SECTIONHARDWARE USED IN THIS SECTION (not actual size)SECTION A: ASSEMBLE THE POLE Phillips-Head Screwdrive
8P/N 21196804 10/041TOPMIDDLEBOTTOM231.Mark pole sections with tape (not supplied) at indicated distances from ends as shown.Tape (Not Supplied)18&quo
10/04 P/N 2119680494.1" (2.54 cm)SIDE VIEWFill hole approximately 1/3full with mixed concrete.FIG. AFLANGEInsert ground sleeve assembly and cente
Comments to this Manuals